Skip to content
Call or text (608) 927-6750
A new wall-mounted tankless water heater with copper lines, brass valves and a white vent pipe on a block basement wall, a bucket and tools on a drop cloth

Water Heater Maintenance in Hard Water: Flush, Anode, Valve

Updated

Get a free quote

A licensed plumber replies with a price. Nothing is booked until you say yes.

Rather talk? Call (608) 927-6750 or text us.

Short answer

Part of Tankless Water Heaters.

A water heater that gets a little attention lasts longer and fails less dramatically. This guide covers the routine checks a homeowner can do on a tank heater, the repairs that are worth paying for, and the point where replacement is the better buy. If you are shopping for a new unit instead, start with tankless water heater installation or the water heater replacement section on the homepage.

Why Beloit water is hard on water heaters

The City pumps groundwater from eight wells, and its 2024 water quality report lists hardness of 280 to 400 mg/L, which the City converts to 16 to 23 grains per gallon (2024 CCR). Heating hard water drops calcium and magnesium out of solution, and in a tank heater it settles on the bottom as sediment. That layer is what makes a gas heater rumble or pop as the burner runs, and it insulates the water from the flame, so the heater works harder for the same hot water. In an electric heater the lower element can end up buried in it. The Beloit hard water guide covers hardness in the towns around the city.

Flushing a water heater

Flushing means draining water from the tank's drain valve until it runs clear, carrying sediment out with it. The exact steps and how often to do it are in the heater's manual, and they differ for gas and electric units. The general order:

  1. Turn the gas control to pilot or vacation, or switch off the breaker for an electric heater.
  2. Close the cold water supply valve on top of the heater.
  3. Attach a garden hose to the drain valve and run it to a floor drain.
  4. Open a hot faucet upstairs to let air in, then open the drain valve.
  5. Drain until the water runs clear, close the valve, refill with a hot tap open until water flows, then restore power or gas.

On an older heater that has never been flushed, the plastic drain valve can clog or refuse to reseal. If it drips after closing, a plumber can replace it. Never turn an electric heater back on before the tank is full again; the elements burn out dry.

The anode rod

Most tank heaters have a sacrificial anode rod, a metal rod screwed into the top of the tank that corrodes so the steel tank does not. When it is used up, the tank starts to rust from the inside. Checking it means turning off the water and power, relieving pressure, and unscrewing the rod with a large socket; the manual names the location and the replacement type. A rod worn down to its core wire is due. A rotten-egg smell from the hot water is sometimes tied to the anode as well; ask a plumber before swapping rod types.

The relief valve

The temperature and pressure relief valve near the top of the tank is the heater's safety valve. Wisconsin's code requires a combination valve rated for the heater, with a discharge pipe that runs by gravity, has no valve in it, and ends within 6 inches of the floor or a receptor in the same room (SPS 382.40(5)(d)). Many manuals call for lifting the lever briefly to make sure it opens and reseats. A valve that keeps dripping afterward needs attention; the relief valve guide explains the causes, including the closed-system pressure that an expansion tank is there to absorb.

Common repairs and what they cost

ProblemUsual fix
No hot water, electricReset the high-limit switch, or replace an element or thermostat
Not enough hot water, electricLower element failed or buried in sediment
No hot water, gasPilot, thermocouple or gas control valve
Rumbling or poppingSediment; flush the tank
Dripping relief valvePressure or temperature problem, or a worn valve
Water under the tankFind the source first: fittings and valves are repairable, a leaking tank is not

National 2026 guides put water heater repairs at $150 to $750 and a standard tank replacement at $881 to $1,826 installed (Angi, HomeAdvisor). Every price is on the plumber cost page.

When to stop repairing and replace

  • The tank itself is leaking or rusting through. There is no repair for that.
  • The heater is near the end of its rated life and needs a part that costs a good share of a new one.
  • Repairs keep coming back every year.
  • The household has outgrown it; see what size water heater you need.

A replacement in Beloit is plumbing work under the City's code, which requires a permit before work starts; the fee schedule lists $50 to file plus $7 per appliance (2026 fee schedule). The permits guide has the details, and a water softener is the long-term fix for the sediment that started all this.

Who may do it

Wisconsin exempts minor repairs to appliances, valves and controls from the plumbing license requirement, and an owner may do plumbing in the one-family home they live in (Wis. Stat. 145.06). Gas valves, venting and anything that smells of gas are jobs for a professional. If you smell gas, leave the house and call Alliant Energy at 1-800-255-4268 from outside (Alliant gas safety).

Want a price for your own house?

Call, text, or send the form. You get a price back before any work is scheduled.

Quick answers

How often should I flush my water heater?

Follow the schedule in the heater's manual. In hard water like Beloit's, 16 to 23 grains per gallon, sediment builds faster, so a heater that rumbles is overdue.

Why does my water heater make a popping noise?

Sediment on the bottom of the tank. Water trapped under it flashes to steam as the burner heats it. Flushing usually quiets it; heavy buildup can mean replacement is near.

When should a water heater anode rod be replaced?

When it is worn down to its core wire. Check it on the schedule the manual gives; in hard water rods can wear unevenly.

How much does it cost to replace a water heater element?

Element and thermostat replacements fall within typical water heater repairs, $150 to $750 in national 2026 guides. See the cost page.

Is it worth repairing an old water heater?

Repair parts are worth it on a sound tank. A leaking or rusting tank is not repairable, and a standard replacement runs $881 to $1,826 installed. See the cost page.

Can I maintain my own water heater in Wisconsin?

Wisconsin exempts minor repairs to appliances and controls from the license requirement, and owners may work on their own one-family home. Leave gas valves and venting to a professional.

Want a plumber to look at it?

Describe the problem and the town. A licensed plumber replies with a price before any work starts.

Prices and the full service list are on the homepage for a plumber in Beloit.