Skip to content
Call or text (608) 927-6750
Inside an older sink cabinet: new braided supply lines and chrome shut-off valves, an adjustable wrench, an old faucet cartridge and a rag

Water Hammer: Why Pipes Bang and How to Stop It

Updated

Get a free quote

A licensed plumber replies with a price. Nothing is booked until you say yes.

Rather talk? Call (608) 927-6750 or text us.

Short answer

Part of Faucet and Shower Repair.

A single hard knock when a faucet shuts is usually harmless. Repeated banging is a sign something in the system needs attention, and a licensed plumber who handles faucet repair is often the first to look at it. This guide covers what water hammer is, what Wisconsin code says, the other causes and the fixes.

What water hammer is

Water moving through a pipe has weight and speed. When a valve snaps shut, that moving water stops all at once and the energy has nowhere to go, so it slams back through the pipes. The result is a bang, a thump or a rattle. Washers, dishwashers and ice makers use solenoid valves that close in a fraction of a second, which is why they are the usual culprits.

What Wisconsin code requires

SPS 382.40(8)(f) says all plumbing fixtures, appliances and appurtenances with 3/8 inch or larger inlet openings and with solenoid-actuated quick-closing valves must be provided with water hammer arrestors (SPS 382.40(8)). In everyday terms, that means a clothes washer or a dishwasher hookup. The arrestors must be accessible, so a plumber can get to one later to service or replace it.

This is not a whole-house requirement. A house with no solenoid appliance does not need an arrestor under that clause, and a house with one needs it at that appliance. If you are in South Beloit, Rockton or Roscoe, Illinois plumbing rules apply instead of the Wisconsin code, and a plumber licensed in Illinois will know what they call for.

Other causes of banging pipes

CauseWhat it sounds likeWhat a plumber checks
Quick-closing valveA sharp bang when a washer or dishwasher stops fillingWhether an arrestor is installed and working
High pressureBanging at several fixtures, often with dripping faucetsPressure with a gauge; the reducing valve
Loose pipe strapsRattling or knocking that follows the pipe runStraps and supports in basements and walls
Worn faucet partsChatter or squeal as the faucet closesWashers, cartridges and seats
Waterlogged air chamberKnock returns after it had stoppedAir chambers or arrestors at the fixture

The first two are the most common. The high water pressure guide explains the 80 psig limit and how to test with a gauge. If the gauge reads high, a reducing valve may quiet the whole system.

What you can check yourself

  • Note which fixture or appliance is on when the bang happens.
  • Look at exposed pipes in the basement for loose or missing straps.
  • Check whether the banging follows the washer or dishwasher cycle.
  • Test your pressure with a hose-bib gauge.

Do not drain the lines to refill air chambers unless you know where the shutoff is and how to restore it. If you need that, the shutoff guide explains where to find the main valve.

How a plumber stops it

A plumber will first find the source. A bang that starts when the washer shuts points to an arrestor at the washer supply valves, usually a small cylinder that screws between the hose and the valve. A bang across the house points to pressure. A rattle that follows a pipe run points to a strap. Each has a different fix, so a quote should name which one the plumber found.

For a faucet that chatters, the fix may be a cartridge or washer swap. A typical faucet job runs $150 to $600 (Angi faucet cost guide). The plumber cost page lists other typical ranges.

Why it matters

Repeated hydraulic shock stresses joints, valves, supply hoses and fixture seals. It can loosen fittings and wear out parts sooner than normal. It also tends to get worse as scale builds up on valves. Beloit water is hard, at 16 to 23 grains per gallon (2024 water quality report), and mineral buildup can make parts stick or close unevenly.

Arrestors and air chambers

Older homes sometimes have a short capped pipe, called an air chamber, stubbed up behind a faucet or washer valve. The trapped air acts as a cushion. Over time the air can dissolve into the water and the chamber fills, and the cushion is gone. Water hammer arrestors do the same job with a sealed piston or bladder that does not run out. That is why code names arrestors and why a plumber often replaces a failed air chamber with one.

Arrestors screw onto the washer supply valves or sit in the wall behind a service panel. The code calls for them to be accessible so they can be replaced. If yours is buried behind finished drywall with no access, say so when you ask for a quote.

Finding the source one appliance at a time

  1. Run the washer through a fill cycle and listen at the supply valves.
  2. Run the dishwasher, then the ice maker line, and note which one bangs.
  3. Open and close each faucet by hand, fast and slow.
  4. Flush each toilet and listen for a knock as the fill valve closes.

If only one appliance bangs, the fix is usually local to that line. If everything bangs, look at pressure. If the sound travels along one wall or ceiling, a loose strap is the likely cause. A plumber can often settle it in a single visit once the source is clear.

What to tell the plumber

A good description saves time. Say which fixtures bang, whether it happens when water starts or stops, and what time of day it is worst. Mention any recent work, such as a new washer, a new water heater or a change to the main line. If you have a pressure reading, bring it. If the noise started right after a repair, a loose strap or a missing support from that job is a likely cause and worth mentioning.

Most banging pipe calls end with one of four fixes: an arrestor, a strap, a pressure adjustment or a worn faucet part. A plumber can usually tell you which after listening to the pipes and reading a gauge, so the quote does not need to be a guess. If it turns out to be several causes at once, the plumber should list them separately so you can approve each.

When to call a plumber

Call when the banging is loud, repeats at every shutoff, or comes with leaks or high pressure. Send the details through the quote form, and mention which fixture or appliance seems to start it.

Want a price for your own house?

Call, text, or send the form. You get a price back before any work is scheduled.

Quick answers

What causes water hammer?

Water hammer happens when flowing water is stopped fast, usually by a quick-closing solenoid valve in a washer or dishwasher. High pressure, loose pipe straps and worn faucet parts can also cause banging.

Does Wisconsin require water hammer arrestors?

SPS 382.40(8)(f) requires them on fixtures and appliances with 3/8 inch or larger inlets that have solenoid-actuated quick-closing valves, and they must be accessible. It is not a blanket whole-house rule.

Can high water pressure cause banging pipes?

High supply pressure makes every shutoff hit harder. Code requires a pressure reducing valve when pressure exceeds 80 psig, and a gauge on a hose bib shows where you stand.

How do I stop pipes from banging?

A plumber finds the source first, then adds or replaces an arrestor, secures loose pipes, lowers the pressure or repairs a worn faucet part. Which one applies depends on when and where the bang happens.

Is water hammer dangerous?

A single bang is usually harmless, but repeated shock can loosen joints and wear valves and hoses. Have it checked if it is loud, constant or paired with leaks.

How much does a faucet repair cost?

Faucet replacement typically runs $150 to $600 in national cost guides. See the cost page for other jobs.

Want a plumber to look at it?

Describe the problem and the town. A licensed plumber replies with a price before any work starts.

Prices and the full service list are on the homepage for a plumber in Beloit.